Maytag cme9010cae Installation Instructions Manual

Download Installation instructions manual of Maytag cme9010cae Microwave Oven for Free or View it Online on All-Guides.com.

Brand: Maytag

Category: Microwave Oven

Type: Installation instructions manual for Maytag cme9010cae

Pages: 17

Download Maytag cme9010cae Installation instructions manual

Maytag cme9010cae Installation instructions manual - Page 1
1
Maytag cme9010cae Installation instructions manual - Page 2
2
Maytag cme9010cae Installation instructions manual - Page 3
3
Maytag cme9010cae Installation instructions manual - Page 4
4
Maytag cme9010cae Installation instructions manual - Page 5
5
Maytag cme9010cae Installation instructions manual - Page 6
6
Maytag cme9010cae Installation instructions manual - Page 7
7
Maytag cme9010cae Installation instructions manual - Page 8
8
Maytag cme9010cae Installation instructions manual - Page 9
9
Maytag cme9010cae Installation instructions manual - Page 10
10
Maytag cme9010cae Installation instructions manual - Page 11
11
Maytag cme9010cae Installation instructions manual - Page 12
12
Maytag cme9010cae Installation instructions manual - Page 13
13
Maytag cme9010cae Installation instructions manual - Page 14
14
Maytag cme9010cae Installation instructions manual - Page 15
15
Maytag cme9010cae Installation instructions manual - Page 16
16
Maytag cme9010cae Installation instructions manual - Page 17
17
24(]EdwarosS[reetSE
C]evelan_Tennessee,37(]_I
TeL:423472-3333
Fax:473478-67!0
NOTE: It is important to pick the correct screw length needed for your cabinets. If the screw is too shore, it
will not reach the oven. If the screw is too long, it will not permit the oven to draw up to the cabinet snugly.
See Figure 20
CABINET
FRONT . CABINET BO'I-I'OM SHELF
_ FILLER BLOCK
"1
MICROWAVE OVEN TOP
FIG, 20
5. Locate the rectangular slot on the left rear wall of the oven inside the left grease filter opening. See Figure
FIG. 21
NOTE: For high capacity vent model, the oven bottom plate may have to be opened to access the slot.
6. Use the rectangular washer (Hardware Item 7) to mark a hole for drilling in the left side rectangular slot.
Place the washer in the slot by grasping the "*ears" on the washer to center in the opening. Mark the center of
the hole in the washer onto the rear wall with a pencil. Center carefully to assure a good fit.
7. Drill a small pilot hole with a 1/8" drill to determine ifa stud is behind the hole. Ifa stud is found, drill a
3/16" diameter hole for a wood screw; if no stud is found, drill a 5/8" diameter hole for a toggle bolt.
8. Ifa stud was found, use a wood screw (Hardware Item I) to be inserted through the rectangular washer
(Hardware Item 7). Screw into the 3/16" diameter hole. Then twist washer 90 degrees to lock before tighten-
ing. See Figure 22. If no stud was found, use a toggle bolt (Hardware Item 2). Remove toggle and insert bolt
through rectangular washer; replace toggle and screw into 5/8" diameter hole as above and tighten. See Figure
22.
FIG. 22
9. Replace grease filters.
10. For top exhaust, replace the exhaust adaptor by twisting into slits of the blower plate and squaring adap-
tor. Reinstall damper and connect house duct pipe to exhaust adaptor. (Before connecting house duct pipe,
make sure that the damper blade is movable by exhaust air).
[] ;',,t_'_TAG Admlr_i 31 "_'--JENN-,_I_ _'llacji(: Chet