Aficio C811DN Quick Installation Manual

Download Quick installation manual of Aficio C811DN Printer for Free or View it Online on All-Guides.com.

Brand: Aficio

Category: Printer

Type: Quick installation manual for Aficio C811DN

Pages: 4

Download Aficio C811DN Quick installation manual

Aficio C811DN Quick installation manual - Page 1
1
Aficio C811DN Quick installation manual - Page 2
2
Aficio C811DN Quick installation manual - Page 3
3
Aficio C811DN Quick installation manual - Page 4
4
Pulling the handle, slowly open the
inner cover.
ATU611S
Remove the orange tapes from the
printer.
ATU612S
Pull out the tapes horizontally. Be sure
to pull out all four strips of tape.
ATU613S
To avoid malfunctions, be sure to remove all four
strips of tape from the photo conductor unit.
Removed tape is dirty. Be careful not to let it touch
your hands or clothes.
Pressing both sides, firmly close the
inner cover.
ATU614S
Push up the lever on the right side, and
open the printer's right cover carefully.
ATU607S
While pushing the lever, remove the secur-
ing pin by pulling the wire with the red tag.
ATU608S
Close the right cover firmly until it
clicks.
Holding the left and right side grips,
carefully open the front cover.
ATU609S
Turn the two green levers counterclock-
wise.
ATU610S
Optimum Environmental Conditions
Permissible and recommended temperature and humid-
ity ranges are as follows:
%RH
TS4K031KE
White area: Permissible Range
Gray area: Recommended Range
The machine must be level within 5 mm, 0.2˝ from
both front to rear and left to right.
To avoid possible build-up of ozone, locate this
machine in a large well ventilated room that has an
air turnover of more than 30 m
3
/hr/person.
When you use this machine for a long time in a
confined space without good ventilation, you may
detect a smell. To keep the workplace comfortable,
we recommend that you keep it well ventilated.
Do not use the printer in the following environments:
Areas exposed to direct sunlight or strong light
Dusty areas
Areas with corrosive gases
Areas that are excessively cold, hot, or humid
Locations near air conditioners or humidifiers
Locations near other electronic equipment
Locations subject to frequent strong vibration
Power Source
Connect the power cable to a power source of the fol-
lowing specification:
120 V, 60 Hz, 12 A or more
Quick Installation Guide
Read this manual carefully before you use the product and keep it handy for future reference.
For safe and correct use, please be sure to read the Safety Information in “Safety Information”
before using the machine.
Unpacking
To protect it from shock and vibration during transit,
this printer comes packaged in cushioning foam and
secured with tape. Remove these protective materials
after bringing the machine to where it will be installed.
Caution
When lifting the machine, use the grips on
both sides. The printer could break or cause
an injury if dropped.
Place no objects on the front or inner cover.
Pull out the handle.
ATU604S
Lift the printer with four people by us-
ing the handles on both sides of the
printer.
ATU605S
Leave the tape in place while moving the printer.
Lower the machine slowly and carefully to prevent
trapping your hands.
Return the handle you pulled out from
the printer to its original position.
Remove the tape indicated by the arrow.
Do not remove the four strips of tape at-
tached to the front cover.
ATU606S
Checking the included
items
Follow the procedure below to verify the items that
come with the printer.
Ensure that the box contains all items listed below.
The items, except for the Quick Installation Guide
and toner, are in tray 1. If there are any missing or
defective items, contact your sales representative.
Manuals and CD-ROMs
Quick Installation Guide (This manual)
CD-ROM “Printer Drivers and Utilities”
CD-ROM “Manuals”
CD-ROM “Document Management Utility”
Ferrite Core
ATU602S
Power Cable
Toner: Black (K), Magenta (M), Cyan
(C), Yellow (Y)
ATU1601S
Color Calibration Sample Sheet
Additional Documentation
This package does not include an interface cable.
Purchase one as necessary to connect to the printer.
Where to Put the Printer
The printer’s location should be carefully chosen
because environmental conditions greatly affect its
performance.
Warning
Confirm that the wall outlet is near the machine and
freely accessible, so that in event of an emergency, it
can be unplugged easily.
Only connect the machine to the power source
described on this manual.
Avoid multi-wiring.
Do not damage, break or make any modifications to
the power cord. Do not place heavy objects on it, pull
it hard or bend it more than necessary. These actions
could cause an electric shock or fire.
The supplied power cord is for use with this equipment
only. Do not use with other appliances. Doing so may
result in fire, electric shock, or injury.
Caution
Do not handle the plug with wet hands. Doing so might
cause an electrical shock.
Keep the machine in an area that is within optimum
environmental conditions. Operating the machine in
an environment that is outside the recommended
ranges of humidity and temperature can cause an
electrical fire hazard. Keep the area around the socket
free of dust. Accumulated dust can become an
electrical fire hazard.
Place the machine on a strong and level surface.
Otherwise, it might fall and injure someone.
If you use the machine in a confined space, ensure
there is continuous air circulation.
Space Required for Installation
Leave enough space around the printer to operate it
freely. The recommended minimum space is as follows:
ATU600S
: 75 cm (29.6 inches) or more
: 60 cm (23.7 inches) or more
: 10 cm (4 inches) or more
: 60 cm (23.7 inches) or more
: 67 cm (26.4 inches) or more
: 67 cm (26.4 inches) or more
CLP240D
C7640nD
LP440c
Aficio SP C811DN