Milwaukee 6065 Operator's Manual

Download Operator's manual of Milwaukee 6065 Grinder, Sander for Free or View it Online on All-Guides.com. This version of Milwaukee 6065 Manual compatible with such list of devices, as: 6065, 6065-6, 6066-6, 6072, 6078

Milwaukee 6065 Operator's manual - Page 1
1
Milwaukee 6065 Operator's manual - Page 2
2
Milwaukee 6065 Operator's manual - Page 3
3
Milwaukee 6065 Operator's manual - Page 4
4
Milwaukee 6065 Operator's manual - Page 5
5
Milwaukee 6065 Operator's manual - Page 6
6
Milwaukee 6065 Operator's manual - Page 7
7
Milwaukee 6065 Operator's manual - Page 8
8
Milwaukee 6065 Operator's manual - Page 9
9
Milwaukee 6065 Operator's manual - Page 10
10
Milwaukee 6065 Operator's manual - Page 11
11
Milwaukee 6065 Operator's manual - Page 12
12
Milwaukee 6065 Operator's manual - Page 13
13
Milwaukee 6065 Operator's manual - Page 14
14
Milwaukee 6065 Operator's manual - Page 15
15
Milwaukee 6065 Operator's manual - Page 16
16
Milwaukee 6065 Operator's manual - Page 17
17
Milwaukee 6065 Operator's manual - Page 18
18
Milwaukee 6065 Operator's manual - Page 19
19
Milwaukee 6065 Operator's manual - Page 20
20
Milwaukee 6065 Operator's manual - Page 21
21
Milwaukee 6065 Operator's manual - Page 22
22
Milwaukee 6065 Operator's manual - Page 23
23
Milwaukee 6065 Operator's manual - Page 24
24
Milwaukee 6065 Operator's manual - Page 25
25
Milwaukee 6065 Operator's manual - Page 26
26
Milwaukee 6065 Operator's manual - Page 27
27
Milwaukee 6065 Operator's manual - Page 28
28
Milwaukee 6065 Operator's manual - Page 29
29
Milwaukee 6065 Operator's manual - Page 30
30
Milwaukee 6065 Operator's manual - Page 31
31
Milwaukee 6065 Operator's manual - Page 32
32
4
Additional Safety Warnings
Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
lead from lead-based paint
crystalline silica from bricks and cement and other
masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
GROUNDING
WARNING
Improperly connecting the ground-
ing wire can result in the risk of
electric shock. Check with a qualied electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not t the outlet, have a
proper outlet installed by a qualied electrician.
Grounded Tools (Three-Prong Plugs)
Tools marked “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
“live” terminal.
Your tool must be plugged into an appro-
Fig. A
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
Double Insulated Tools (Two-Prong Plugs)
Tools marked “Double Insulated” do not require
grounding. They have a special double insulation
system which satisfies OSHA requirements and
complies with the applicable standards
Fig. B
Fig. C
of Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in either
of the 120 volt outlets shown in Figures
B and C.
side of cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied
to these wheels may cause them to shatter.
Always use undamaged wheel anges that are of
correct size and shape for your selected wheel.
Proper wheel anges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel anges.
Do not use worn down wheels from larger power
tools. Wheel intended for larger power tool is not
suitable for the higher speed of a smaller tool and
may burst.
Additional Safety Warnings Specic for Abrasive
Cutting-Off Operations:
Do not “jam” the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases
the loading and susceptibility to twisting or binding
of the wheel in the cut and the possibility of kickback
or wheel breakage.
Do not position your body in line with and behind
the rotating wheel. When the wheel, at the point of
operation, is moving away from your body, the pos-
sible kickback may propel the spinning wheel and
the power tool directly at you.
When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the
cut-off wheel from the cut while the wheel is in
motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of
wheel binding.
Do not restart the cutting operation in the work-
piece. Let the wheel reach full speed and care-
fully re-enter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece."
Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on
both sides of the wheel.
Use extra caution when making a “pocket cut”
into existing walls or other blind areas. The pro-
truding wheel may cut gas or water pipes, electrical
wiring or objects that can cause kickback.
Safety Warnings Specic for Sanding Operations:
Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding
paper extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing
of the disc or kickback.
Safety Warnings Specic for Wire Brushing Op-
erations:
Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush. The wire bristles can easily penetrate
light clothing and/or skin.
If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work load
and centrifugal forces.